CBI - Reference

Preparing surfaces, plugging leaks, making good cracks and defects, ready to receive the waterproofing system Mastic asphalt waterproofing Applying primer to vertical surfaces Isolating membranes Internal angle fillets Turning top edges into grooves, etc. Sealant to edges of waterproofing Board, drainage cell and other protection against mechanical damage Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrates, plugging leaks, making good cracks and defects, ready to receive the waterproofing system Applying primers Cold-applied coatings including two-component materials Hot-applied coatings Glass fibre or other reinforcement Sand blinding Board, drainage cell and other protection against mechanical damage Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrates, plugging leaks, making good cracks, imperfections and defects, ready to receive the waterproofing system Roller, spray or brush applied coatings of liquid-applied plastics to internal and/or external surfaces Glass fibre or other reinforcement Board, drainage cell and other protection against mechanical damage Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrates, plugging leaks and making good cracks and defects ready to receive the waterproofing system Applying primers Applying bituminous and plastics single or multi-layer sheeting, self bonded or using bonding compounds Lapped and sealed joints, welted joints Adhesive jointing tape Board, drainage cell and other protection against mechanical damage Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrates and making good cracks and defects Applying drainage cell sheet damp-proofing to external surfaces Board and/or other protection against mechanical damage if required Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Preparing surfaces, plugging leaks, making good cracks and defects, ready to receive the tanking or dampproofing system Latex emulsions or aqueous liquids applied to concrete surfaces internally or externally Potassium or sodium silicate gel applied to concrete surfaces Application of sealant around service lines where they penetrate the concrete surfaces Non-fixed work (see Explanatory notes)

Preparing surfaces, plugging leaks, making good cracks and defects, ready to receive the tanking system Applying bonding agents Dubbing out Single or multi-coat work of cement-based coatings Sprayed, trowelled, floated and similar surface finishes Control joints Metal beads, nosings, stops, etc. Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

"Building underlays including appropriate jointing and lapping methods Tapes and fixings Flexible flashings at head and sill Roof underlays including appropriate jointing and lapping methods Underlay supports Foils, vapour barriers and vapour control membranes including appropriate jointing and lapping methods, plus tapes, seals and fixings DPM and Dpc's including appropriate jointing and lapping methods, plus tapes and fixings Forming, dressing and sealing openings as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)"

No content available for this item.

Rigid air barriers including appropriate jointing methods Tapes and fixings Flexible flashings at head and sill Forming, dressing and sealing openings as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

No content available for this item.

No content available for this item.

Members of steel, stainless steel, aluminium, bronze, etc., framed together and fixed to building structure Cleats, brackets, bolts, connections and fixings for securing the curtain wall to the building structure Windows, panels, doors, shutters, etc., supplied and fixed as an integral part of the assembly, including all associated hardware Photovoltaic cells incorporated into the facade, connected to the electrical supply system Glazing components, sealants, intumescent sealants, gaskets, distance pieces, location blocks, setting blocks, etc. Standard and special hardware Internal trims Flashings, soakers, cappings, etc., against adjoining work when executed as part of the curtain walling, as needed to make the walling weatherproof Preparing surfaces and applying protective coatings and decorative finishes off site and on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Performance criteria Contractor design and shop drawings Non-fixed work (see Explanatory notes)

Exposed grid of steel, stainless steel, aluminium, bronze, timber, concrete etc., fixed to the building structure with all required cleats, bolts, brackets and other connectors Cladding between the exposed grid, of windows, panels, doors, shutters, etc., of all types including all associated hardware Photovoltaic cells incorporated into the cladding, connected to the electrical supply system Glazing components, sealants, intumescent sealants, gaskets, distance pieces, location blocks, setting blocks, etc Standard and special hardware Internal finishing trim Flashings, soakers, cappings, etc., against adjoining work when executed as part of the cladding, as needed to make the walling weatherproof Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Prefabricated panels, constructed of or faced with glass, including profiled glass, metal, ceramics, plastics or composite materials, prepared to receive windows, doors, etc., where required and incorporating insulation, internal linings and sheet finishes Windows, doors, glazing, etc., factory fitted to the prefabricated panels, with all associated hardware and accessories, where so specified Back-up walling, when part of the facade system Installation of panels as facade cladding, with all required cleats, brackets, bolts Photovoltaic cells incorporated into the cladding, connected to the electrical supply system Flashings, soakers, cappings, etc., against adjoining work when executed as part of the curtain walling, as needed to make the walling weatherproof Standard and special hardware Internal finishing trim Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Members of steel, stainless steel, aluminium, bronze, etc., framed together to form walling, arcades, vaults and roofs and fixed to the building structure ready to receive glazing Cleats, brackets, bolts, connections and fixings, securing the framing to the building structure Opening frames, etc., with associated hardware, where forming an integral part of the metal walling, arcade, vault or roof Glazing, with safety glass or plastics, with glazing compounds, metal beads, sealants, gaskets, capping strips, etc., where the glazing forms an integral part of the metal walling, arcade, vault or roof Flashings, soakers, cappings, etc., against adjoining work when executed as part of the installation Internal finishing trim Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Solid timber boards, profiled, ship lap, butt jointed or tongued and grooved, fixed horizontally, diagonally or vertically Building wraps and thermal insulation fixed at the same time as the cladding Cover battens, beads, fillets, soakers, jointing strips, cover strips, etc., to joints and junctions Flashings and weatherproofing of the cladding against adjacent materials Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Manufactured timber boards, with plain or textured surface, with profiled, ship lap, T&G or butt joints, to simulate weatherboards, shingles, etc. fixed as cladding Building wraps and thermal insulation fixed at the same time as the manufactured timber boarding Cover battens, beads, fillets, soakers, cover strips, sealants, etc. Flashings and weatherproofing of cladding against adjacent materials Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Plywood with plain or textured surface, with profiled, shiplap, spline, T&G or butt joints, fixed as cladding Building wraps and thermal insulation fixed at the same time as the cladding Cover battens, beads, fillets, soakers, jointing strips, cover strips, etc., to joints and junctions Flashings and weatherproofing of the cladding against adjacent materials Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Decorative trim associated with the cladding systems if not included with them

Prefabricated panels, with timber or metal edge framing and with intermediate studs or solid or honeycomb core Insulation, vapour proofing and waterproof layers incorporated into the panel Solid timber and/or manufactured timber boarding, external facing Substrate and/or finished linings, fixed to the inner face of the panel Panels erected with interlocking joints or between posts, as either infill or weight-bearing walling Panels prepared to receive or provided with building services Weatherproofing, including flashing, sealants, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fibre cement flat sheets, with or without surface finish texture Fibre cement flat sheets simulating timber weatherboards Fibre cement columns Cover moulds, jointing strips, etc. Sealants to joints Reinforcement to joints Building wraps, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Sheets of steel, stainless steel, aluminium, copper and zinc, flat, embossed, modelled or shaped with edges formed to suit the jointing system, fixed to framing Imitation weatherboarding Sheets of steel, stainless steel, aluminium, copper and zinc, as facing to composite panels with insulation and backing sheets, flat or shaped, with edges formed to suit jointing system, fixed to framing Cover moulds, jointing strips, etc. Sealants to joints Building wraps, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat sheets of mineral fibre with edges prepared to suit the jointing system, fixed to framing Flat sheets of inert materials prepared for external use, with edges prepared to suit the jointing system, fixed to framing Flat sheets of organic materials, bound with synthetic resins Flat sheets of mineral and/or organic fibre and other inert materials as facing to composite panels with insulation and backing sheets, with edges formed to suit jointing system, fixed to framing Cover moulds, jointing strips, etc. Sealants to joints Building paper, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Sheets of rigid plastics, flat, embossed or shaped, including twin-wall sheets, with edges formed to suit the jointing system, fixed to framing Imitation weatherboarding Flat or shaped sheets of rigid plastics as facing to composite panels with insulation and backing sheets, and with edges formed to suit jointing system, fixed to framing Cover moulds, jointing strips, etc. Sealants to joints Building wrap, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat sheets, with or without surface finish texture Cover moulds, jointing strips, etc. Sealants to joints Reinforcement to joints Building wraps, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Profiled sheets of steel, stainless steel, aluminium, copper and zinc, fixed to framing Metal profiled sheets as facing to composite panels with insulation of all types and backing sheets, fixed to framing Profiled sheets of steel, with multi-layers of metallic and non-metallic coatings as a protective coating, fixed to framing Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the cladding installation Building wrap, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the cladding installation Secondary supports required for the cladding, when fixed at the same time and as part of the cladding installation All necessary fixings All jointing of the sheets, with necessary sealants and jointing strips Flashings, beddings and trim required to provide a weathertight installation Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Plastics profiled sheets fixed to framing Plastics profiled sheets as facing to composite panels with insulation and backing sheets, fixed to framing Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the cladding installation Building paper, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the cladding installation Secondary supports required for the cladding, when fixed at the same time and as part of the cladding installation All necessary fixings All jointing of the sheets, with necessary mastics, sealants and jointing strips Flashings, beddings and trim required to provide a weathertight installation Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fibre cement profiled sheets, including sheets with false joints and accessories formed as part of the sheets, fixed to framing Fibre cement profiled sheets as facing to composite panels with insulation and backing sheets, fixed to framing Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the cladding installation Building wrap, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the cladding installation Secondary supports required for the cladding, when fixed at the same time and as part of the cladding installation All necessary fixings All jointing of the sheets, with necessary sealants and jointing strips Flashings, beddings and trim required to provide a weathertight installation Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Profiled sheets of bitumen-impregnated or resin impregnated organic and/or mineral fibre, with or without a top coating to provide colour or protection, fixed to framing Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the cladding installation Building wrap, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the cladding installation Secondary supports required for the cladding, when fixed at the same time and as part of the cladding installation All necessary fixings All jointing of the sheets, with necessary mastics, sealants and jointing strips Flashings, beddings and trim required to provide a weathertight installation Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes) On site finishes (66-11)

Proprietary cladding systems, with panels formed with two sheets of aluminium bonded to a plastic resin or foamed plastics, mechanically fixed to the building fabric, with all joints sealed Paint finish to the aluminium sheeting if not prefinished Proprietary cladding panels formed of two aluminium skins bonded to an aluminium honeycomb core, the long sides of the panels with upturned edge, fixed to the building fabric with proprietary fixing clamps Proprietary cladding panels of two sheets of aluminium, bonded to a plywood core, with fixing clips secured to the rear face of the panels, interconnecting with clips fixed to the building fabric Panel faces embossed, textured or plain Panels finished with powder coating, paint, anodising, applied plastics sheet or unfinished Windows, doors and openings incorporated as required as part of the cladding system Sealants to joints Proprietary framing and fixing systems Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Proprietary cladding systems of steel or aluminium unbacked panels, the long edges of the panels formed to provide interlocking joints, fixed to the building fabric with the panels running vertically, horizontally or diagonally, secured to proprietary brackets Panels formed of prefinished steel or painted or anodised aluminium Windows, doors and openings incorporated as required as part of the cladding system Sealants to joints Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Proprietary cladding systems of panels, consisting of a frame faced with self-finished plastic sheeting, backed or unbacked, secured to the building fabric with a proprietary fixing system Plastics facade panels or claddings, self-finished or to receive site finish Insulation or backing incorporated into the panels and linings Accessories and fixings, including accessories supplied and placed as part of the work of other Work sections Windows, doors and openings incorporated as required as part of the cladding system Sealants to joints Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Proprietary facade panels, with steel or timber frame and studs, the external face finished with rigid plastics insulating sheet with trowelled plaster surface, the rear face finished with plasterboard or fibre cement board. Panels joined by fillet set into grooves in the edges of the panels. Supply and installation Paint finish to panels Windows doors and openings incorporated as required as part of the cladding system Sealants to joints Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

"Proprietary cladding systems, fixed to steel or timber framing, concrete block or brick veneer, consisting of foam plastics rigid insulating board covered with plaster reinforced with fibreglass mesh, precoloured or paint finished Windows doors and openings incorporated as required as part of the cladding system Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)"

Proprietary wall cladding system with fibre cement sheeting fixed to timber or steel framed walling, the sheet joints and angles reinforced and the surface finished with plaster, with or without fibreglass mesh reinforced, with the surface appropriately textured and finished with an acrylic-based paint Windows doors and openings incorporated as required as part of the cladding system Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Proprietary cladding system consisting of foamed plastics (various) insulation, with steel sheet bonded to both faces, the sheeting prefinished and the panel finished with interlocking joints at panel junctions Panels set on horizontal floor surfaces and tilted to a vertical position, with interlocking joints where panels abut and fixed to wall framing at the upper level Panels used as long span roofing Windows doors and openings incorporated as required as part of the cladding system Sealants to joints as required Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Proprietary cladding systems of pre-finished panels, secured to the building fabric with one of several proprietary fixing systems Facade panels or claddings, self-finished Insulation or backing incorporated into the panels and linings Accessories and fixings, including accessories supplied and placed as part of the work of other Work sections Windows, doors and openings incorporated as required as part of the cladding system Jointing systems Sealants to joints Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Windows doors and openings incorporated as required as part of the cladding system Sealants to joints Panels fixed to the building structure Proprietary panel systems, with panels, framed together, the outer face covered with panels, etc. Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility

Brickwork of clay bricks, concrete bricks and calcium silicate bricks of all types Special shape bricks, including grooved bricks for services Specially faced bricks Walls laid in bonds and with surface patterns Flue linings Steel sheets, holed for ties for securing masonry veneers, fixed to the building fabric Purpose-made centring and formwork Mortar, pointing materials Bagging Accessories, flashings, thresholds, sills, lintels, etc., built into the brickwork Joint reinforcement Sealants Wall ties, anchors, cramps, dowels, restraining members Flexible dpc’s, slate dpc’s, termite shields Metal dpc’s built in and extended out as flashing over sloping surfaces Cavity trays formed from flexible sheet dpc material Preformed cavity trays Galvanized steel lintels Rigid sheet and foil insulation and building wrap when installed as part of the brickwork Cavity wall ventilators, fire barriers, weepholes Cavity bridging ducts Flue terminals Members to provide seismic restraint to panels Movement joints and fillers Forming and cutting brickwork Cleaning down Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Hollow concrete blocks of all types Special shape blocks Specially faced blocks Blocks with knock-out and cut-out sections Lintel blocks Purpose-made centring and formwork Reinforcement Mortar Accessories, flashings, thresholds, sills, lintels, etc., built into the blockwork Anchors, cramps, dowels, restraining members Dpc’s, termite shields Metal dpc’s built in and extended out as flashing over sloping surfaces Cavity trays formed from flexible sheet dpc material Movement joints and fillers Forming and cutting blockwork Sealants Cleaning down Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Solid concrete blocks of all types Aerated autoclaved concrete solid blocks of all types (AAC) Special shape blocks Specially faced blocks Purpose-made centring and formwork Reinforcement Mortar Special mortars and adhesives Accessories, thresholds, sills, etc., built into the blockwork Anchors, cramps, dowels Dpc’s, termite shields Cavity trays formed from flexible sheet dpc material Movement joints and fillers Members to provide seismic restraint to panels, fixed to structural frame Forming and cutting blockwork Sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fired-clay blocks of all types Special shape blocks, including grooved blocks Specially faced blocks Purpose-made centring and formwork Mortar Accessories thresholds, sills etc built into the blockwork Anchors cramps and dowels Dpc’s, termite shields Cavity trays formed from flexible sheet dpc material Movement joints and fillers Members to provide seismic restraint to panels, fixed to structural frame Forming and cutting blockwork Sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Unfired earth blocks and bricks of all types Special shape blocks and bricks Purpose-made centring and formwork Accessories built into or fixed to the earth masonry Dpc’s, termite shields Movement joints and fillers Forming and cutting earth masonry Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Natural stone of all types, worked to required sizes and finishes, of thickness to carry its own weight Rubble stonework, squared or random, coursed or uncoursed Dressed stonework Ashlar stonework Decorative stonework, including balusters, columns, string courses, fireplace surrounds, etc. Walling, including piers and buttresses, coursed or uncoursed Shaped stones to form openings, quoins, arches, sills, copings, corbels, etc. Facework bonded or tied to a backing or to supports Purpose-made centring and formwork Mortar and cementitious filling Accessories built into the stonework Dpc’s, termite shields, etc. Movement joints and fillers Sealants Rigid sheet and foil insulation and building wrap when installed as part of the stonework Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Thin natural stone of all stone types Rubble stonework, squared or random, coursed or uncoursed Dressed stonework Ashlar stonework Mortar and cementitious filling Accessories built into the stonework Movement joints and fillers Sealants Rigid sheet and foil insulation and building wrap when installed as part of the facade walling system Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

"Thin simulated stone of all types Mortar, cementitious and synthetic filling Accessories built into the stonework Movement joints and fillers Sealants Rigid sheet and foil insulation and building wrap when installed as part of the facade walling system Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)"

Masonry walling of reconstructed stone or of precast concrete simulated stone, laid with dry or mortar coursed joints, to form veneers Reconstructed stone of required sizes and finishes Precast concrete simulated stone blocks of required sizes and finishes Walling, including piers and buttresses, coursed or uncoursed of thickness to carry its own weight Facework tied to a backing or to supports Decorative masonry including balusters, columns, sills, copings, arches, pediments and other features Chimney stacks Precast lintels Galvanised steel lintels Purpose-made centring and formwork Mortar and cementitious filling Accessories built into the masonry Dpc’s, termite shields, etc. Movement joints and fillers Sealants Rigid sheet and foil insulation and building wrap when installed as part of the masonry Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Cement or polymer modified reinforced or non reinforced plaster applied by trowel pump or spray Expanded metal, wire mesh and other lathing, fixed to framed or solid backgrounds as a base and key for plaster, rendering, roughcast and sprayed coatings, where not included with the coating Framing of folded sheet metal members for solid plaster partitions Furring of folded sheet steel members for columns and beam casings, suspended ceilings, etc. Plain expanded metal lathing Ribbed expanded metal lathing Steel wire netting Welded mesh lathing with integrated paper backing Gypsum board lathing Timber lathing Fixing lathing to framed or to solid backings Steel rod stirrups, spacer rods and hangers Screws, staples, clips, clout nails, wire ties, steel banding and other fixings Flashings of aluminium, stainless steel or uPVC Unfixed work Proprietary paint systems

Tilt slab and in situ concrete structures Brick and concrete block veneer Concrete block masonry walls Autoclaved aerated concrete block and panels Insulated concrete formwork (ICF) or EPS polystyrene blocks Plaster mixes Sliplayer of building wrap Control joints, trim, beads, exterior cavity vermin proofing Proprietary paint systems

uPVC control joints, trays, flashings, jointing tapes Primers Fibreglass reinforcing mesh Flashings of aluminium, stainless steel or uPVC Cement free fibre reinforced plaster Premixed coloured finishing renders Proprietary paint systems

Rigid cellular polystyrene Cavity battens Fibreglass reinforcing mesh uPVC flashings and accessories Hot dipped galvanised steel flat head nails and plastic washers Self tapping steel screws and plastic washers Plaster render systems Proprietary paint systems

Plaster render system over tilt slab and in situ concrete structures Plaster render system over brick and concrete block veneer Plaster render system over concrete block masonry walls Plaster render system over autoclaved aerated concrete block and panels Insulation and fixings Reinforcing mesh Flashings, control joints and accessories Plaster render systems Proprietary paint systems

No content available for this item.

No content available for this item.

Profiled sheets, including textured and curved sheets of steel, including factory-coated colour finished steel, stainless steel, aluminium, copper and zinc, fixed to framing Metal profiled sheets as facing to composite panels with backing of manufactured timber boards, insulation of all types, and backing sheets, fixed to framing Metal profiled sheets and plastics insulation of the same profile, factory or site assembled, fixed to framing Profiled sheets of steel, with multi-layers of metallic and non-metallic coatings as a protective coating, fixed to framing Acoustic treatment to reduce impact and external noise Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the roof covering installation Underlays, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the roof covering installation Secondary supports required for the roof covering, when fixed at the same time and as part of the roof covering installation All necessary fixings All jointing of the sheets, with necessary sealants and jointing strips Flashings, flexible pipe boots, beddings and trim required to provide a weathertight installation Integral ventilating ridges Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Profiled plastics sheets, including specially formed and faced sheets, fixed to framing Plastics profiled sheets as facing to composite panels, with backing of manufactured timber boards, insulation of all types, and backing sheets, fixed to framing Plastics profiled sheets and plastics insulation of the same profiles, factory or site assembled, fixed to framing Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the roof covering installation Underlays, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the roof covering installation Secondary supports required for the roof covering, when fixed at the same time and as part of the roof covering installation Required safety precautions including steel mesh, fixed under and at the same time as the roofing with signs etc. All necessary fixings All jointing of the sheets, with necessary sealants and jointing strips Flashings, flexible pipe boots, beddings and trim required to provide a weathertight installation Integral ventilating ridges Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fibre cement profiled sheets, including accessories formed as part of the sheet, fixed to framing Fibre cement profiled sheets as facing to composite panels, with backing of manufactured timber boards, insulation of all types, and backing sheets, fixed to framing Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the roof covering installation Underlays plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the roof covering installation Secondary supports required for the roof covering, when fixed at the same time and as part of the roof covering installation Required safety precautions, including steel mesh, fixed under and at the same time as the roof covering, with signs, etc. All necessary fixings All jointing of the sheets, with necessary sealants and jointing strips Flashings, beddings and trim required to provide a weathertight installation Integral ventilating ridges Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Profiled sheets of bitumen-impregnated cellulose fibre with the top surface protected by a melamine coating, fixed to framing Bitumen-impregnated cellulose fibre sheets, used as an underlay to low-pitch tile roofs Ridge capping and other accessories made of the same material Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the roof covering installation Building paper, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the roof covering installation Secondary supports required for the roof covering, when fixed at the same time and as part of the roof covering installation Required safety precautions including steel mesh, fixed under and at the same time as the roofing with signs etc. All necessary fixings All jointing of the sheets, with necessary mastics, sealants and jointing strips Flashings, beddings and trim required to provide a weathertight installation Integral ventilating ridges Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Profiled sheets of bitumen-impregnated or resin impregnated organic and/or mineral fibre, with or without a top coating to provide colour or protection, fixed to framing Translucent and transparent plastics sheets of the same profiles, fixed at the same time as the installation Sheet linings of fibre cement, manufactured timber boards and other rigid sheets, fixed under and at the same time and as part of the cladding installation Underlays, plastics sheeting, reflective insulation, and board and blanket insulation, when fixed as part of the cladding installation Secondary supports required for the cladding, when fixed at the same time and as part of the cladding installation All necessary fixings All jointing of the sheets, with necessary sealants and jointing strips Flashings, beddings and trim required to provide a weathertight installation Cover moulds, trim, expansion joints, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Solar panels, of any material, integral with the profiled roofing, for collecting solar radiation Interconnecting the energy/heat-absorbing medium to convey the collected energy/heat to, heat exchangers/converters, and storage mediums Fixing panels to supporting framework Required safety precautions Cover moulds, jointing strips, sealants etc. Underlays of building paper, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Single lap and double lap concrete tiles, with interlocking edges, of required size and finish, fixed to battens Matching glass and plastics translucent tiles Vents, vent tiles and ridge and finial capping tiles Hip irons External angles to wall-hanging Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Underlays, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Sealants; pigmented mortar for bedding Flashings, flexible pipe boots and trims required to provide a weathertight installation Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Clay tiles, plain and of all shapes, with or without interlocks at edges, of required size and finish, fixed to battens Matching glass and plastics translucent tiles Vents, vent tiles and ridge and finial capping tiles Hip irons External angles to wall-hanging Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Sealants; pigmented mortar for beddings Flashings, flexible pipe boots and trims required to provide a weathertight installation Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Corrosion-protected steel sheet, pressed into tile form, with decorative finish, fixed to battens Matching accessories, including ridge and hip cappings, barges, fascias and eaves Cutting at valleys, openings and abutments, including sealing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Sealants Flashings, flexible pipe boots and trims required to provide a weathertight installation Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Rigid plastics single or double lap tiles, fixed to battens Matching glass and plastics translucent tiles Vents, vent tiles and ridge and finial capping tiles Hip irons External angles to wall-hanging Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Sealants Flashings, flexible pipe boots and trims required to provide a weathertight installation Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat sheets of fibre cement, with or without surface texture Preparation of edges prepared to suit the jointing system Flat sheets of fibre cement, as facing to composite panels, with backing of manufactured timber boards, insulation and backing sheets, fixed to framing Required safety precautions including steel mesh Cover moulds, jointing strips, etc. Underlays of building paper, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Insulation applied on top of the roofing in the form of gravel, foamed plastics, reflective coatings, when installed as part of the roofing installation Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat sheets of steel, stainless steel, aluminium, copper and zinc, as facing to composite panels, with insulation and backing sheets, with edges formed to suit jointing system, fixed to framing Cover moulds, jointing strips, etc. Underlays of building paper, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Composite sheets in panel form, consisting of a core of insulating plastics, faced on both sides with steel, aluminium and/or stainless steel sheet, with edges formed to provide a jointing system, fixed to framing Cover moulds, trim, etc. Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Glass-faced panels of sandwich construction, including insulation Glass-faced panels and tiles incorporating photovoltaic cells, the panels electrically connected to supply electricity to the building Fixing panels to supporting framework Required safety precautions including steel mesh Cover moulds, jointing strips, sealants etc. Underlays of building paper, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Solar panels, of any material, integral with the flat panel roofing, for collecting solar radiation Interconnecting the energy/heat-absorbing medium to convey the collected energy/heat to, heat exchangers/converters, and storage mediums Fixing panels to supporting framework Required safety precautions including steel mesh Cover moulds, jointing strips, sealants etc. Underlays of building paper, plastics sheeting, reflective insulation, board and blanket insulation when fixed as part of the installation Flashings when fixed as part of the installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Thermal insulation, wraps, underlays and/or rigid air barriers fixed at the same time as the plywood Plywood roofing or decking, fixed to framing, complete with fillets and other trim Including falls, upstands, gutters, sumps, outlets and other plywood clad related items Sanding, sealing and otherwise preparing surfaces to receive protective/waterproof coatings and decorative finishes Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Natural slate, including stone slate, in sheet form, cut to required sizes, prepared for fixing and fixed with nails to battens or interlocking battens Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, using exposed or concealed metal flashings, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Mastics and sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fibre cement sheets, cut or formed to required size to simulate natural slate, prepared for fixing, laid horizontally or diagonally and fixed to battens Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Mastics and sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Reconstructed stone, precast concrete and other cement-based slates, cast in shape and with texture and colour to simulate natural slates, fixed to battens Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Mastics and sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Rigid plastics in size, colour and surface texture to simulate natural slate, with or without interlocking joints, fixed to battens Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Mastics and sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fully supported thermoplastic or flexible plastics or rubber sheeting, cut to simulate slating and secured with adhesives Forming eaves and barges, including drip edge Forming closed cut valleys Hips and ridges formed from the asphalt sheeting Plastics or sheet metal valleys, gutters, hips, ridges, etc. Soakers, flashings and flexible pipe boots, of all types to provide a weathertight installation Underlays and plastics sheeting when fixed at the same time and as a part of the installation Plywood substrates All necessary fixings Sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Sawn timber shingles and split timber shakes, fixed to battens Shingles of manufactured timber boarding, embossed with woodgrain pattern Forming eaves, including clips and gap filler Forming verges, including undercloaks, bedding and pointing Forming ridges and hips, including ends, angles and intersections, bedding and pointing Cutting at valleys, openings and abutments, including bedding and pointing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Mastics and sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Corrosion-protected steel sheet, pressed into forms similar to timber shingles and shakes, with decorative finish, fixed to battens Matching accessories, including ridge and hip cappings, barges, fascias and eaves Cutting at valleys, openings and abutments, including sealing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Mastics and sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Copper sheet, pressed into forms similar to timber shingles and shakes, fixed to batten Matching accessories, including ridge and hip cappings, barges, fascias and eaves Cutting at valleys, openings and abutments, including sealing Valley and back gutters, soakers and flashings of all types to provide a weathertight installation Underlays of building papers, plastics sheeting, reflective insulation and board and blanket insulation when fixed at the same time and as a part of the installation Battening and counterbattening when fixed as a part of the installation All necessary fixings Mastics and sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fully supported fibre-reinforced asphalt shingles, with mineral or ceramic granules on exposed faces, fastened and/or stuck to substrate Fully supported fibre reinforced asphalt shingles, with flat sheet aluminium or copper on exposed faces Saturated felt underlay Forming eaves and barges, including drip edge Forming closed cut valleys Hips and ridges formed from the asphalt sheeting Plastics or sheet metal valleys, gutters, hips, ridges, etc. Soakers, flashings and flexible pipe boots, of all types to provide a weathertight installation Underlays and plastics sheeting when fixed at the same time and as a part of the installation Plywood substrates All necessary fixings Sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flexible sheets of built-up felt, cut to shape of multiple shingles, with natural or applied surface finish, nailed to substrate Accessories of plain built-up felt sheets Primers, bonding and adhesive compounds, including lap, joint and flashing tapes Forming eaves and barges, including drip edge Forming closed cut valleys Hips and ridges formed from the sheeting Plastics or sheet metal valleys, gutters, hips, ridges, etc. Soakers, flashings and flexible pipe boots, of all types to provide a weathertight installation Underlays and plastics sheeting when fixed at the same time and as a part of the installation Plywood substrates All necessary fixings Sealants Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Fully supported flat steel sheeting, with factory-applied anti-corrosive protective coating, as roof covering, with standing seams, rolls and cross welts Linings to gutters, valleys and cesspools, where fixed as part of the installation Fascias Underlays and plastics sheeting, where fixed as part of the installation Underlays of board insulation, where fixed as part of the installation Rain-noise reducing underlays Plywood substrates Fixing clips, expansion clips, tacks, screws and other fixings Mesh coverings to cesspools Associated flashings, back gutters and cappings Wedging into grooves Coating underside of roofing with bitumen to form an isolation layer Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat sheet stainless steel, of selected grade and surface finish, including annealed and impressed finish, and/or terne coated, as roof covering, with standing seams, rolls and cross welts Linings to gutters, valleys and cesspools, where fixed as part of the installation Fascias Underlays and plastics sheeting, where fixed as part of the installation Underlays of board insulation, where fixed as part of the installation Rain-noise reducing underlays Plywood substrates Fixing clips, expansion clips, tacks, screws and other fixings Mesh coverings to cesspools Associated flashings, back gutters and cappings Wedging into grooves Coating underside of roofing with bitumen to form an isolation layer Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat aluminium sheeting of selected grade and surface finish, including embossed finish, as a roof covering, with standing seams, rolls and cross welts Linings to gutters, valleys and cesspools, where fixed as part of the installation Fascias Underlays and plastics sheeting, where fixed as part of the installation Underlays of board insulation, where fixed as part of the installation Rain-noise reducing underlays Plywood substrates Fixing clips, expansion clips, tacks, screws and other fixings Mesh coverings to cesspools Associated flashings, back gutters and cappings Wedging into grooves Coating underside of roofing with bitumen to form an isolation layer Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat copper and bronze sheeting with standing seams, rolls and cross welts Sheet copper in standardized sheet sizes with preformed standing seams and end joints Linings to gutters, valleys and cesspools, where fixed as part of the installation Fascias Underlays and plastics sheeting, where fixed as part of the installation Underlays of board insulation, where fixed as part of the installation Rain-noise reducing underlays Plywood substrates Fixing clips, expansion clips, tacks, screws and other fixings Mesh coverings to cesspools Associated flashings, back gutters and cappings Wedging into grooves Coating underside of roofing with bitumen to form an isolation layer Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat zinc and zinc alloy sheeting with standing seams, rolls and cross welts Linings to gutters, valleys and cesspools, where fixed as part of the installation Fascias Underlays and plastics sheeting, where fixed as part of the installation Underlays of board insulation, where fixed as part of the installation Rain-noise reducing underlays Plywood substrates Fixing clips, expansion clips, tacks, screws and other fixings Mesh coverings to cesspools Associated flashings, back gutters and cappings Wedging into grooves Coating underside of roofing with bitumen to form an isolation layer Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Flat lead sheeting with standing seams, rolls and cross welts Linings to gutters, valleys and cesspools, where fixed as part of the installation Fascias Underlays and plastics sheeting, where fixed as part of the installation Underlays of board insulation, where fixed as part of the installation Rain-noise reducing underlays Plywood substrates Fixing clips, expansion clips, tacks, screws and other fixings Mesh coverings to cesspools Associated flashings, back gutters and cappings Wedging into grooves Coating underside of roofing with bitumen to form an isolation layer Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Complete with gutters and downpipes Electric motors and power supply

No content available for this item.

Manufactured boards, planks or panels, of any material including, individual spaced boards, tongue and groove, composite panels etc fixed to framing or on proprietary decking supports, forming a nonwaterproof deck surface. Accessories and components for fixing and support Preparing surfaces to receive finishes on or off site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Timber boards or planks, including individual spaced boards, tongue and groove, truck decking etc fixed to framing, forming a non-waterproof deck surface. Sanding, sealing and otherwise preparing surfaces for finishes off site Preparing surfaces to receive finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Manufactured boards, planks or panels, of any material including, individual spaced boards, tongue and groove, composite panels etc fixed to framing or on proprietary decking supports, forming a nonwaterproof deck surface. Accessories and components for fixing and support Preparing surfaces to receive finishes on or off site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Standard, purpose made and proprietary anti-slip applied finish, constructed of steel, stainless steel, aluminium, bronze, plastics, carborundum, fibreglass, composite materials, etc. Strips of safety and anti-slip tape applied to the surface. Anti-slip inlay strips either in the surface of the timbert decking or placed between. Anti-slip mesh applied to the surface including boardwalks.

Insulation in the form of sprayed coatings and reflective coatings, applied to the roofing

Standard, purpose made and proprietary roof vents and frames, non-glazed, constructed of steel, stainless steel, aluminium, bronze, plastics, metal-cored plastics, timber, timber and metal, composite materials, etc. Roof vents incorporating exhaust fans Fire-rated roof vents Automatically opening roof vents Sliding, swivelling and rotating roof vents Ancillary items, where an integral part of the roof vent, including hardware, trim, flashings, operating gear, security screens, insect barriers, etc. Installing in roofing and covering, with all necessary anchors, fixings, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

No content available for this item.

Preparation of substrate, including priming and filling cracks Mastic asphalt roof coverings, including sand blinding Surfacings of asphalt and/or roofing asphalt to multi-storey car parks Bitumen-based dry screeds Vapour barriers Primers and bonding compounds including taping substrate joints Felt, glass fibre and similar underlays Metal lathing Movement joints and cappings Internal angle fillets Edges, drips, arrises, turning nibs into grooves, etc. Work to duct covers, flashings, etc. Skirting and aprons Gutters, channels, valleys and kerbs, sumps and roof drains Metal edge trim and anchor strips Solar reflective coating, where installed as part of the work Insulation, above or below the membrane, where installed as part of the work Chips and/or gravel where installed as part of the work Vents to release vapour from below the membrane Paving tiles, etc., including any supporting stools, where installed as part of the roofing work Wire mesh covers to sumps Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Preparing the substrate to receive the membrane Mineral fibre reinforced bitumen based sheeting bonded to mineral fibre or polyester bituminous felt, supplied in rolls, to near flat and pitched roofs, fully supported, with lapped joints in single or multiple layers, fully or partially bonded to the substrate Membrane carried up and down vertical surfaces, turned into grooves at edge, extended as linings to box and shaped gutters and sumps, with fillets at internal angles Finished at eaves and exposed edges with aluminium trim or turned over timber battens Movement joints, rolled joints, cappings, etc. Solar reflective and protective coating and sheeting where installed as part of the work Insulation, above or below the membrane, where installed as part of the work Chips and/or gravel where installed as part of the work Vents to release vapour from below the membrane Paving tiles, etc., including any supporting stools, where installed as part of the work Wire mesh covers to sumps Metal edge trim and anchor strips Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing the substrate to receive the membrane Synthetic rubber sheet roofing, in roll form, bonded to the substrate or loose laid, with lapped and sealed joints Membrane carried up and down vertical surfaces, turned into grooves at edge, extended as linings to box and shaped gutters and sumps, with fillets at internal angles Finished at eaves and exposed edges with aluminium trim or turned over timber battens Movement joints, rolled joints, cappings, etc. Solar reflective and protective coating and sheeting where installed as part of the work Insulation, above or below the membrane, where installed as part of the work Chips and/or gravel or pebble ballast where installed as part of the work Vents to release vapour from below the membrane Paving tiles, etc., including any supporting stools, where installed as part of the work Wire mesh covers to sumps Metal edge trim and anchor strips Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrate to receive the membrane Modified bitumen sheet roofing in single or multiple layers, without or with reinforcing of woven or non-woven fabric of glass or synthetic fibres, with or without a protective plastics film self-coloured or with adhered granule finish, laid with lapped and sealed joints, the membrane bonded or torched onto the substrate Membrane carried up and down vertical surfaces, turned into grooves at edge, extended as linings to box and shaped gutters and sumps, with fillets at internal angles Special landscape and planting membranes where installed as part of the work Finished at eaves and exposed edges with aluminium trim or turned over timber battens Movement joints, rolled joints, cappings, etc. Solar reflective and protective coating and sheeting where installed as part of the work Insulation, above or below the membrane, where installed as part of the work Chips and/or gravel or pebble ballast where installed as part of the work Vents to release vapour from below the membrane Paving tiles, etc., including any supporting stools, where installed as part of the work Wire mesh covers to sumps Metal edge trim and anchor strips Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrate to receive membrane Sheet plastics in single or multiple layers, with or without a reinforcing fabric, with a self-coloured or applied finish, laid loose or bonded to the substrate, with lapped and sealed joints Membrane carried up and down vertical surfaces, turned into grooves at edge, extended as linings to box and shaped gutters and sumps, with fillets at internal angles Finished at eaves and exposed edges with aluminium trim or turned over timber battens Movement joints, rolled joints, cappings, etc. Solar reflective and protective coating and sheeting where installed as part of the work Insulation, above or below the membrane, where installed as part of the work Chips and/or gravel or pebble ballast where installed as part of the work Vents to release vapour from below the membrane Paving tiles, etc., including any supporting blocks, where installed as part of the work Wire mesh covers to sumps Metal edge trim and anchor strips Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Preparing substrate to receive membrane including priming coat Liquid-applied plastics, with or without reinforcing fabric and fibres, in selected colours, applied in single or multiple coats Liquid-applied aqueous acrylic coating, with or without reinforcing fabric or fibres, in selected colours, applied in single or multiple coats Single layer coating to shower bases and other wet areas internally Forming verges, gutters, sumps, etc. Solar reflective coating and sheeting when installed as part of the work Insulation, above or below the membrane, where installed as part of the work Chips and/or gravel where installed as part of the work Vents to release vapour from below the membrane Paving tiles, etc., including any supporting blocks, where installed as part of the work Wire mesh covers to sumps Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrate Insulation applied on top of the membrane Loose gravel placed on the roof surface Reflective sheet applied to the membrane or to the board insulation Reflective paint coating applied to the membrane or to the board insulation Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Preparing substrate Installing loose-laid walkway matting Installing trafficable concrete paving tiles directly or on stools Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

ELD systems create a detectable electrical potential difference between a non-conductive membrane and a grounded conductive substrate (e.g. reinforced slab) or conductive underlay over non-conductive substrate (e.g. wire mesh over ply). Test with low voltage detection equipment by applying water (conductive) to the surface of the membrane. Includes connection points and temporary detection equipment, if required, conductive underlays and permanent detection/monitoring equipment.

Standard, purpose made and proprietary roof vents and frames, non-glazed, constructed of steel, stainless steel, aluminium, bronze, plastics, metal-cored plastics, timber, timber and metal, composite materials, etc. Roof vents incorporating exhaust fans Fire-rated roof vents Automatically opening roof vents Sliding, swivelling and rotating roof vents Ancillary items, where an integral part of the roof vent, including hardware, trim, flashings, operating gear, security screens, insect barriers, etc. Installing in roofing and covering, with all necessary anchors, fixings, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Gratings and outlets Sumps Overflow Outlets

No content available for this item.

No content available for this item.

Suites of timber windows, doors and roof lights, including hinged, pivoting, sliding/folding, sliding/stacking, rolling, revolving and sliding sashes and doors, timber fixed lights, hatches, panels, etc., associated frames, and installed in the external face Insect screening when supplied with the suites Privacy and solar screening when supplied with the suites Glazing, ventilation panels, etc., supplied and fixed on/off site Supplying and fixing hardware, and fixing hardware supplied by others Architraves, trim, etc., when supplied with the suites Sealants and airseals Weatherbars and head, sill and jamb flashings when supplied with the suites Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Timber decorative screens, including associated frames Timber screens and associated frames to openings, including louvres, wire mesh screening to air intake and relief openings to exclude rain, animals and debris Timber screens and associated frames and supports, fixed externally or internally to control heat and light, with fixed or adjustable blades Timber shutters to doors and windows, hinged or sliding, fixed externally or internally Timber lightproof fixed louvred screens and frames Securing screens and shutters to the building fabric, with all necessary anchors, fixings, etc. Hardware, operating gear Connecting electrically operated items to a designated point of electrical supply Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Standard, purpose made and proprietary fixed or hinged timber roof windows and lights, including lights with metal external facing, complete with glazing Proprietary roof and balcony timber windows Glazed lights, set into ceilings Window control gear Rain sensor controlled roof lights Blinds, screens, ventilation incorporated in the roof lights Ancillary items where an integral part of the roof lights and frames, including glazing, hardware, lighting, firerated ceiling barrier, trim, vents, security screens, insect barriers, operating gear and flashings Associated light-transmitting ductwork to illuminate spaces below, including glazed sash to seal lower end Installing into roofing Preparing surfaces and applying decorative finishes off site Preparing surfaces to receive decorative finishes on site Non-fixed work (see Explanatory notes)

Suites of aluminium windows, doors and frames, including hinged, pivoting, sliding/folding, sliding/stacking, rolling, revolving and sliding sashes and doors, aluminium fixed lights, hatches, panels, etc., installed in external walling Aluminium sub frames Insect screening when supplied with the suites Privacy screening when supplied with the suites Sun control louvres where integral with window Supplying and fixing hardware, and fixing hardware supplied by others Glazing, ventilation panels, etc., supplied and fixed on/off site Architraves, trim, etc., when supplied with the suites Sealants and airseals Weatherbars and head, jamb and sill flashings when supplied with the suites Contractor design and shop drawings Installation Sill supports Preparing surfaces and applying protective coatings and decorative finishes off site Non-fixed work (see Explanatory notes)

Aluminium decorative screens, including associated frames Aluminium security screens to openings, including associated frames, fixed externally or internally Aluminium screens and associated frames to openings, including louvres and wire mesh screening to air intake and relief openings, to exclude rain, sound, animals and debris Screens of perforated aluminium sheet, woven or mesh aluminium wire, fixed to building facades Aluminium screens and baffles, with associated frames and supports, fixed externally or internally to control light and heat, with fixed or adjustable blades of metal, glass, plastics, etc. Aluminium shutters to doors and windows, hinged or sliding, fixed externally or internally Aluminium lightproof fixed louvred screens and frames Securing screens and frames to the building fabric with all necessary anchors, fixings, etc. Hardware, operating gear, etc. Connecting electrically operated adjustable screens and louvres to a designated point of electrical supply Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Standard, purpose-made and proprietary fixed or hinged aluminium roof windows and lights, complete with glazing Glazed lights set into ceilings Blinds, screens, ventilation incorporated in roof lights Automatic-venting roof lights Rain sensor controlled roof lights Associated light-transmitting ductwork to illuminate spaces below, including glazed sash to seal lower end Fans forming part of the installation Ancillary items where an integral part of the roof lights and frames, including glazing, hardware, lighting, firerated ceiling barrier, trim, vents, security screens, insect barriers, operating gear and flashings Installing in roofing Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

No content available for this item.

Suites of steel windows, doors and frames, including hinged, pivoting, sliding/folding, sliding/stacking, rolling, revolving and sliding sashes and doors, aluminium fixed lights, hatches, panels, etc., installed in external walling Steel sub frames Insect screening when supplied with the suites Privacy screening when supplied with the suites Sun control louvres where integral with window Supplying and fixing hardware, and fixing hardware supplied by others Glazing, ventilation panels, etc., supplied and fixed on/off site Architraves, trim, etc., when supplied with the suites Sealants and airseals Weatherbars and head, jamb and sill flashings when supplied with the suites Contractor design and shop drawings Installation Sill supports Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Steel decorative screens, including associated frames Steel security screens to openings, including associated frames, fixed externally or internally Steel screens and associated frames to openings, including louvres, acoustic louvres and wire mesh screening to air intake and relief openings to exclude sound, rain, animals and debris Screens of perforated sheet steel, woven or mesh steel wire, fixed to building facades Steel screens and baffles, with associated frames and supports, fixed externally or internally to control light and heat, with fixed or adjustable blades of metal, glass, plastics, etc. Steel shutters to doors and windows, hinged or sliding, fixed externally or internally Steel lightproof fixed louvred screens and frames Securing screens and frames to the building fabric with all necessary anchors, fixings, etc. Hardware, operating gear, etc. Connecting electrically operated adjustable screens and louvres to a designated point of electrical supply Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Standard, purpose-made and proprietary fixed or hinged steel roof windows and lights, complete with glazing Glazed lights set into ceilings Blinds, screens, ventilation incorporated in roof lights Automatic-venting roof lights Rain sensor controlled roof lights Associated light-transmitting ductwork to illuminate spaces below, including glazed sash to seal lower end Fans forming part of the installation Ancillary items where an integral part of the roof lights and frames, including glazing, hardware, lighting, firerated ceiling barrier, trim, vents, security screens, insect barriers, operating gear and flashings Installing in roofing Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

No content available for this item.

Suites of plastics windows, doors and frames, including hinged, pivoting, sliding/folding, sliding/stacking, rolling, revolving and sliding sashes and doors, aluminium fixed lights, hatches, panels, etc., installed in external walling Insect screening when supplied with the suites Privacy screening when supplied with the suites Sun control louvres where integral with window Supplying and fixing hardware, and fixing hardware supplied by others Glazing, ventilation panels, etc., supplied and fixed on/off site Architraves, trim, etc., when supplied with the suites Sealants and airseals Weatherbars and head, jamb and sill flashings when supplied with the suites Contractor design and shop drawings Installation Sill supports Non-fixed work (see Explanatory notes)

Plastics decorative screens, including associated frames Plastics security screens to openings, including associated frames, fixed externally or internally Plastics screens and associated frames to openings, including louvres, acoustic louvres and wire mesh screening to air intake and relief openings to exclude sound, rain, animals and debris Plastics screens and baffles, with associated frames and supports, fixed externally or internally to control light and heat, with fixed or adjustable blades of metal, glass, plastics, etc. Plastics shutters to doors and windows, hinged or sliding, fixed externally or internally Plastics lightproof fixed louvred screens and frames Securing screens and frames to the building fabric with all necessary anchors, fixings, etc. Hardware, operating gear, etc. Connecting electrically operated adjustable screens and louvres to a designated point of electrical supply Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Hinged doors of flexible sheet plastics, including hardware Screens to openings of flexible plastics strips including gravity flaps Screens to openings of flexible plastics strips, extending from floor to ceiling, acting as a partition while providing unrestrained access Screens to openings of plastics beads on flexible cords Installation

Standard, purpose-made and proprietary fixed or hinged plastics roof windows and lights, complete with glazing Glazed lights set into ceilings Blinds, screens, ventilation Rain sensor controlled roof lights Automatic-venting roof lights Associated light-transmitting ductwork to illuminate spaces below, including glazed sash to seal lower end Fans forming part of the installation Ancillary items where an integral part of the roof lights and frames, including glazing, hardware, lighting, firerated ceiling barrier, trim, vents, security screens, insect barriers, operating gear and flashings Installing in roofing Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

No content available for this item.

"Composite decorative screens, including associated frames Composite security screens to openings, including associated frames, fixed externally or internally Composite screens and associated frames to openings, including louvres, acoustic louvres and wire mesh screening to air intake and relief openings to exclude sound, rain, animals and debris Composite screens and baffles, with associated frames and supports, fixed externally or internally to control light and heat, with fixed or adjustable blades of metal, glass, plastics, etc. Composite shutters to doors and windows, hinged or sliding, fixed externally or internally Composite fixed louvred screens and frames Securing screens and frames to the building fabric with all necessary anchors, fixings, etc. Hardware, operating gear, etc. Connecting electrically operated adjustable screens and louvres to a designated point of electrical supply Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)"

Preparing surfaces to receive protective coatings and decorative finishes on site Sub frames Insect or security screening when supplied with the suites Doors and frames, including hinged or pivoting, installed in external walling Supplying and fixing hardware, and fixing hardware supplied by others Weatherbars and head, jamb and sill flashings when supplied with the suites Installation Sealants and airseals Architraves, trim, etc., when supplied with the suites Glazing, ventilation panels, etc., supplied and fixed on/off site Preparing surfaces and applying protective coatings and decorative finishes off site Sill supports Contractor design and shop drawings

Standard, purpose-made and proprietary fixed or hinged composite roof windows and lights, complete with glazing Glazed lights set into ceilings Blinds, screens, ventilation incorporated in roof lights Automatic-venting roof lights Rain sensor controlled Associated light-transmitting ductwork to illuminate spaces below, including glazed sash to seal lower end Fans forming part of the installation Ancillary items where an integral part of the roof lights and frames, including glazing, hardware, lighting, firerated ceiling barrier, trim, vents, security screens, insect barriers, operating gear and flashings Installing in roofing Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Suites of composite garage doors and frames, composite fixed lights, hatched, panels, etc., installed in external walling Installation in door frames Composite subframes Composite door frames shaped to suit the doors to be installed Sills and transoms incorporated into the frames Door sets of proprietary composite door frames and composite doors, including hinged, sliding, roll-up, horizontally rolling, up and over, sliding/folding, and sliding/stacking doors Glazing, hardware, ventilation panels, etc., supplied and fixed off site Fixing supplied hardware Architraves, trim, etc., when supplied with the suites Weatherbars and flashings when supplied with the suites Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Suites of stainless steel windows, doors and frames, including hinged, pivoting, sliding/folding, sliding/stacking, rolling, revolving and sliding sashes and doors, stainless steel fixed lights, hatches, panels, etc., installed in external walling Stainless steel sub frames Insect screening when supplied with the suites Privacy screening when supplied with the suites Sun control louvres where integral with window Supplying and fixing hardware, and fixing hardware supplied by others Glazing, ventilation panels, etc., supplied and fixed on/off site Architraves, trim, etc., when supplied with the suites Sealants and airseals Weatherbars and head, jamb and sill flashings when supplied with the suites Contractor design and shop drawings Installation Sill supports Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Stainless steel decorative screens, including associated frames Stainless steel security screens to openings, including associated frames, fixed externally or internally Stainless steel screens and associated frames to openings, including louvres and wire mesh screening, to air intake and relief openings to exclude rain, animals and debris Screens of perforated stainless steel sheet, woven or mesh stainless steel wire, fixed to building facades Stainless steel screens and baffles, with associated frames and supports, fixed externally or internally to control light and heat, with fixed or adjustable blades of metal, glass, plastics, etc. Stainless steel shutters to doors and windows, hinged or sliding, fixed externally or internally Stainless steel lightproof fixed louvred screens and frames Securing screens and frames to the building fabric with all necessary anchors, fixings, etc. Hardware, operating gear, etc. Connecting electrically operated adjustable screens and louvres to a designated point of electrical supply Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Standard, purpose-made and proprietary fixed or hinged stainless steel roof windows and lights, complete with glazing Glazed lights set into ceilings Blinds, screens, ventilation incorporated in roof lights Automatic-venting roof lights Rain sensor controlled roof lights Associated light-transmitting ductwork to illuminate spaces below, including glazed sash to seal lower end Fans forming part of the installation Ancillary items where an integral part of the roof lights and frames, including glazing, hardware, lighting, firerated ceiling barrier, trim, vents, security screens, insect barriers, operating gear and flashings Installing in roofing Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Suites of bronze windows, doors and frames, including hinged, pivoting, sliding/folding, sliding/stacking, rolling, revolving and sliding sashes and doors, stainless steel fixed lights, hatches, panels, etc., installed in external walling Bronze sub frames Insect screening when supplied with the suites Privacy screening when supplied with the suites Sun control louvres where integral with suites Supplying and fixing hardware, and fixing hardware supplied by others Glazing, ventilation panels, etc., supplied and fixed on/off site Architraves, trim, etc., when supplied with the suites Sealants and airseals Weatherbars and head, jamb and sill flashings when supplied with the suites Contractor design and shop drawings Installation Sill supports Preparing surfaces and applying protective coatings off site Non-fixed work (see Explanatory notes)

Standard, purpose-made and proprietary fixed or hinged bronze roof windows and lights, complete with glazing Glazed lights set into ceilings Blinds, screens, ventilation Automatic-venting roof lights Rain sensor controlled roof lights Associated light-transmitting ductwork to illuminate spaces below, including glazed sash to seal lower end Fans forming part of the installation Ancillary items where an integral part of the roof lights and frames, including glazing, hardware, lighting, firerated ceiling barrier, trim, vents, security screens, insect barriers, operating gear and flashings Installing in roofing Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Suites of any metal windows, doors and frames, and roof lights, including hinged, pivoting, sliding/folding, sliding/stacking, rolling, revolving and sliding sashes and doors, fixed lights, hatches, panels, screens, gates etc., installed in external walling Metal sub frames Insect screening when supplied with the suites Privacy screening when supplied with the suites Sun control louvres where integral with suites Rain sensor controlled roof lights Associated light-transmitting ductwork for roof lights to illuminate spaces below, including ceiling fittings Fans forming part of the roof light installation Supplying and fixing hardware, and fixing hardware supplied by others Glazing, ventilation panels, etc., supplied and fixed on/off site Architraves, trim, etc., when supplied with the suites Sealants and airseals Weatherbars and head, jamb and sill flashings when supplied with the suites Contractor design and shop drawings Installation Sill supports Preparing surfaces and applying protective coatings off site Non-fixed work (see Explanatory notes)

Automatic electro/mechnaical doors with leaf and frame of any materials, supply and installation. Pelmets and other accessories. Operators, sensors, motors, locking mechanisms, safety systems

No content available for this item.

Single leaf hinged fire-rated doors and timber frames Double leaf hinged fire-rated doors and timber frames Sliding gravity operated fire-rated doors and timber frames Sliding counterbalanced fire-rated doors and timber frames Hardware incorporated in the fire-rated doors and frames Fire-rated window and frame assemblies with integral hardware Fire-rated roof windows and lights Installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Single leaf hinged fire-rated doors and metal frames Double leaf hinged fire-rated doors and metal frames Sliding gravity operated fire-rated doors and metal frames Sliding counterbalanced fire-rated doors and metal frames Sliding and roll-up fire-rated shutters and metal frames Hardware incorporated in the fire-rated doors and frames Fire-rated window and frame assemblies with integral hardware Fire-rated roof windows and lights Installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Proprietary fire-rated screen assemblies incorporating doors, windows, fixed lights, hatches, shutters, panels, etc., with integral hardware Installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Sound insulated hinged door and frame assemblies, with integral hardware Sound insulated sliding doors and frame assemblies, with integral hardware Sound insulated sliding/stacking door and frame assemblies with integral hardware Sound insulated sliding/folding and pantograph doors and frame assemblies with integral hardware Installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Sound insulated windows of two or more panes, set in single or split frames, for building into prepared openings Hardware, flashings, trim and screens where forming part of the window assembly Installation Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Sealing to openings, holes, and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Security doors and windows Ballistics doors and windows Blast rated doors and windows Radiation protection doors and windows Cell doors Darkroom entry doors Hangar doors Hygiene doors Strong-room doors Heat-insulated doors

Security screens, door grilles and shutters Ballistics screens, door grilles and shutters Blast rated screens and shutters

Seals, shelters and screens, complete with frames, fixed to the building fabric to restrict the entry of rain, heat, dust, animals and insects Ancillary items where an integral part of the barrier Installing in openings in walling and securing with all necessary anchors, fixings, etc. Connecting electrically operated seals and shelters to a designated point of electrical supply Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Turnstiles of steel, stainless steel or aluminium, manually or electrically operated Hinged or pivoted barriers, of steel, stainless steel or aluminium, manually or electrically operated Retractable barriers of steel, stainless steel or aluminium with glass or metal retractable barriers, electrically operated Electrical equipment connected to a designated point of supply

Subframes, when not included in their installation Hardware, when not included in their installation

No content available for this item.

No content available for this item.

Glazing using glass, glazing plastics and laminates of all types, including: - multi-sheet insulating glass units (IGU) - self-cleaning glass - safety glass - ESD glass - Eltrochromic, thermochromic glasses Fire-rated glass in special frames Glass with decorative finishes, screen printing and UV screening, fused on to the surface Etching and surface treatments Laminated glass including special laminates Insulating glass units with blinds and louvred sunscreens incorporated Leadlight panels Installation on site of glass and plastics of all types into openings, windows, doors, shutters, gates, roof lights, window assemblies, balustrades, exposed metal and timber framed facade cladding, vaulting, roofing and walling, precast concrete and prefabricated facade cladding, etc., using putty, sealant, bead, channel, gasket, tape and sealant glazing with distance pieces, location blocks, setting blocks, shims, clips, etc. Simple glass-to-glass joints, including glass reinforcing fins Glass louvre blades All labours including sandblasting, grinding, raking and curved cutting, acid treatment, edge polishing, brilliant cutting, engraving, other surface and edge treatment, bending and curving Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Glazing using glass, glazing plastics and laminates of all types, including: - one-way vision glass - safety glass - switchable glass - decorative cast glass - anti-reflection glass - electrical conducting glass Fire-rated glass in special frames Glass with decorative finishes and screen printing, fused on to the surface Etching and surface treatments Laminated glass including special laminates Double glazed units with blinds incorporated Installation of glass and plastics of all types into frames and openings, windows, doors, partitions, balustrades, floors, ceilings, joinery, picture frames, etc., using putty, sealant, bead, channel, gasket, tape and sealant glazing with distance pieces, location blocks, setting blocks, shims, clips, etc. Frameless glass panel and door installation on site, including proprietary brackets, supports, hinges, hardware, sealant, etc. Installation on site of sundry glass panels as overlays, including mirrors and heated mirrors, splash-backs, decorative panels, tops etc., using mechanical fixings, adhesive, double sided foam tape, frames, spacers, sealant, etc. Loose glass tops and shelf installation, including spacers, cushion supports, shelf supports, etc. Simple glass-to-glass joints, including glass reinforcing fins All labours including sandblasting, grinding, raking and curved cutting, acid treatment, edge polishing, brilliant cutting, engraving, other surface and edge treatment, bending and curving Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Mirrors fixed to walls of bathrooms, toilet areas, dressing rooms, hair dressing facilities, etc., to provide viewers with their reflections Mirrors with integral light fittings and/or electrical elements for condensation control Installation, including frames, anchors and fixings Connecting electrically illuminated and/or heated mirrors to a designated point of electrical supply Non-fixed work (see Explanatory notes)

Glazing using glass, glazing plastics and laminates of all types, including: - Fire-rated glass, insulated, non-insulated and wired - Heat resistant glass and ceramic - Security glass - Anti-bandit glass - Blast resistant glass - Ballistics glass - Security glass blocks - IT shielding glass - X-Ray shielding glass Installing glazing and glass blocks in special frames to achieve required performance Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Films in sheet form applied to glass to control solar radiation, by absorption and/or reflection, including colour control Films in sheet form to provide decorative patterns Films in sheet form applied to strengthen glass and to minimise scattering of broken glass following damage by impact Films sprayed on to glass to control solar radiation by absorption and/or reflection, including colour control Translucent mirroring films for one-way vision

Glass blocks of all types and sizes Frames to openings of aluminium, timber and steel Mortar, reinforcing rods, compressible filler, bedding and jointing mastic (wet jointing) Sealant, reinforcing bars, plastic clips, etc. Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Glass blocks of types and sizes approved for use in fire-rated wall assemblies Mortar, panel anchors and reinforcement Expansion jointing and joint filling and sealing Installing as required to provide the required fire rating Forming openings as required to suit subcontractor and General Contractor responsibility Sealing to openings and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Translucent plastics blocks of all types Frames to openings when part of the installation Jointing, reinforcing and sealing Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Panels with acrylic glazing in small panels, simulating plastics block walling Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

Toughened, toughened/laminated glass of all types Glass fins or similar stiffeners Proprietary fixings including spiders, patches, brackets Pre-drilling glass for fixings, notches and holes Jointing, grouting, sealing Glass shop fronts, walls, entrance screens Glass squash court walls and similar assemblies Frameless glass doors, supplied and fixed or as an integral part of the assembly Frameless glass balustrades Accessories, including framing and hardware to doors, openings, etc. Flashings and weatherproofing of adjoining work when forming part of the structural glass assembly Forming openings as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Safety and/or laminated glass, prepared for fixing and secured to supporting framework Sacrificial glass wearing surfaces Glass structural blocks, installed in metal frames and secured to supports as floor surface Glass structural blocks, set flush into flat roofing to allow light entry Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Frameless toughened glass doors, hinged, pivoting or sliding, installed in openings Unframed toughened glass sheets assembled to form a screen, with or without sealant jointing, with hinged and/or sliding doors incorporated into the screen Associated hardware, including electrical operation Connecting door operators to a designated point of electrical supply Non-fixed work (see Explanatory notes) Frameless glass doors in assemblies (45-21, 45-31, 45-41, 45-51, 46-51)

Glazed screens, with fixed, sliding, pivoted, rolling and hinged doors, to shower, bath and other toilet fittings, including hardware, to provide part or full enclosure Installing screens with mechanical and sealant joints on or adjacent to the toilet fittings Glazing with all types of safety glass and plastics, framed or frameless, using sealants, etc. Simple glass-to-glass joints Decorative treatment to glass and plastics Non-fixed work (see Explanatory notes)

Frameless sheets of toughened glass, each attached to operating equipment which slides and stacks the sheets Associated hardware Electrical operating equipment Connecting operating equipment to a designated point of electrical supply Non-fixed work (see Explanatory notes)

Partitions formed of sheets of full height safety glass Metal edging to top and bottom edges of glass Securing devices to hold glass sheets in position Vertical joints between glass sheets left unfilled or filled with a transparent sealant Forming openings as required to suit subcontractor and General Contractor responsibility Sealing to openings as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Frame items when not part of the installation Door thresholds Plastics drip

Handles Hinges Brackets Bracing

Special sealants when not part of the installation

No content available for this item.

No content available for this item.

Sheet, rigid or flexible board, quilts and blanket insulation, wrapped and unwrapped, installed independently of work included in other Work sections Insulating panels of all types Foamed resin and loose fill insulation, injected or blown into spaces and cavities Liquid-applied thermal insulation Reflective foil insulation Insulating foils, papers and films Reflective membranes and coatings

Batts and blankets placed in position Insulating loose fill Spray-applied sound insulation Rigid and flexible sheet and board insulation Insulating panels of all types, including metal sheeting Insulating quilts, blankets and batts Preformed insulation to pipes, ducts, etc. Non-fixed work (see Explanatory notes)

Timber and/or metal framing to support the lining material Casing of plasterboard, fibrous plaster, calcium silicate, mineral wool and other mineral boards, of the required thickness Fixing lining to framing Forming openings and cutting holes as required to suit sub-contractor and General Contractor responsibility Sealing to openings, holes and joints as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

No content available for this item.

No content available for this item.

No content available for this item.

Cleaning and preparing the substrate by chemical or mechanical means Applying primers and sealers Installing backing strips Preformed and pillow intumescent sealers Gun applied and putty packed intumescent sealers Intumescent jackets to pipes and ducts Bentonite intumescent tapes Pneumatic sealers Preformed sealants and fillers Gun applied sealants and fillers- all types Painting exposed surfaces Non-fixed work (see Explanatory notes)

Custom made flashings not forming part of any proprietary system Flashings by material Flashings by material and location Flashings by material by cladding type Installation of flashings

No content available for this item.

Adhesives by type Adhesives by use with materials and components Application

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

Timber or non-timber handrails Timber stair balustrading, with rails, posts, uprights, newels, etc., with timber balusters, timber balustrading or prepared to receive balustrading infill of other materials Timber barriers and balustrading, with rails, posts, uprights, screening, etc., with timber balusters, timber balustrading or prepared to receive infill screening of other materials Infilling of glass, plastics, non-ferrous metal and other sheet or fabricated material to balustrades and barriers when supplied as part of the balustrading and barriers Fixing all items and associated components to the building fabric including all bolts, cleats, brackets and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Metal or non-metal handrails Metal stair balustrading, with rails, posts, uprights, newels, etc., with metal balusters, metal balustrading or prepared to receive balustrading infill of other materials Metal barriers and balustrading, with rails, posts, uprights, screening, etc., with metal balusters, metal balustrading or prepared to receive infill screening of other materials Infilling of glass, plastics, timber and other sheet or fabricated material to balustrades and barriers when supplied as part of the balustrading and barriers Fixing all items and associated components to the building fabric including all bolts, cleats, brackets and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Handrails of any material Glass stair balustrading Glass barriers and balustrading Infilling of timber, plastics, non-ferrous metal and other sheet or fabricated material to balustrades and barriers when supplied as part of the balustrading and barriers Fixing all items and associated components to the building fabric including all bolts, cleats, channels, pockets, discs, spider fittings, brackets and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

"Barriers and balustrading of any material(s) Handrails of any material(s) Infilling of any material(s) to balustrades and barriers when supplied as part of the balustrading and barriers Fixing all items and associated components to the building fabric including all bolts, cleats, channels, pockets, brackets and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)"

"Systems consisting largely of metal or mixed materials. Structure and supports largely of metal or mixed materials. Barriers and balustrading and handrails when supplied as part of the system Flooring when supplied as part of the system Stairs, steps and ladders when supplied as part of the system Fixing all items and associated components to the building fabric including all bolts, cleats, channels, pockets, brackets and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)"

"Structure and supports frames Hatches or covers when supplied as part of the system Hatches with opening mechanisms, or covers with fixings that allow complete removal Ceiling panel when supplied as part of the system Steps, ladders, platforms and handrails when supplied as part of the system Components and accessories when supplied as part of the system Fixing all items and associated components to the building fabric including all bolts, cleats, channels, pockets, brackets and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)"

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

Barriers at gaps around doors and shutter openings Mesh and multiple-wire barriers fixed to horizontal surfaces Sprung-wire barriers to ridges, hips, etc. Non-setting sealants and gels on horizontal surfaces

Backing rods Masking materials

No content available for this item.

No content available for this item.

Fabricated steel stairs, tread and riser units, including supporting strings and framing for flights and landings, either with solid steel or grille treads and landings, or prepared to receive precast concrete or timber or laminated timber treads and landings Prefabricated steel stairs, including curved and helical stairs, with tread units, strings and vertical supports Fabricated steel stairs, principally of sheet steel, with pans for horizontal surfaces, prepared to receive cementitious or other flooring material Steel ladders, fixed to the building structure, with strings extended as handrails as required Safety hoops, etc., secured to steel ladders Proprietary or non-proprietary loft ladders including associated hatch doors Steel handrails, of hollow or solid section Steel stair balustrading, with rails, posts, uprights, newels, etc., of sheet, hollow or solid steel sections with steel balusters, steel balustrading or prepared to receive balustrading infill of other materials Steel barriers and balustrading, with rails, bars, pipes, mesh screening, etc., of steel or prepared to receive infill screening of other materials Infilling of glass, plastics, non-ferrous metal and other sheet or fabricated material to balustrades and barriers when supplied as part of the balustrading and barriers Fixing all items and associated components to the building fabric including all bolts, cleats and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Purpose-made steel lining to floor pits, trenches and recesses Purpose-made removable steel floor covers, solid or grated, and associated frames and edging, to floor pits and trenches Proprietary manhole and inspection pit covers and frames Proprietary gratings and frames Purpose-made steel hatches and frames to floor and roof openings, with opening gear Building in or securing frames to the building fabric with all necessary anchors, fixings, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Fire-rated steel framed floor and roof hatches and frames Fire-rated steel covers and frames Fire-rated steel access panels and frames

Steel bollards, angle guards, rubbing strakes and column protection Steel storage racks for general storage, pipes, etc. Steel storage racks for cages, utensils, containers, etc. Steel bicycle racks Steel racks for gas cylinders Fabricated brackets and supports Steel plaques, notices, signs, etc. Steel supports for signs, notices, lights, etc. Steel purpose made safes Steel grates, grilles and trim to fireplaces Steel access panels and frames Steel edgings and fascias Steel weatherbars when not supplied with the frames to openings Cast steel items Steel decorative items Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Sheet steel casing to structural members Sheet steel box gutters, including supports Purpose-made sheet steel linings to openings and recesses Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Fabricated stainless steel stairs, tread and riser units, including supporting strings and framing for flights and landings, either with solid stainless steel or grille treads and landings, or prepared to receive precast concrete or timber or laminated timber treads and landings Prefabricated stainless steel stairs, including curved and helical stairs, with tread units, strings and vertical supports Fabricated stainless steel stairs, principally of sheet stainless steel, with pans for horizontal surfaces, prepared to receive cementitious or other flooring material Stainless steel ladders, fixed to the building structure, with strings extended as handrails as required Safety hoops, etc., secured to stainless steel ladders Proprietary or non-proprietary loft ladders including associated hatch doors Stainless steel handrails, of hollow or solid section Stainless steel stair balustrading, with rails, posts, uprights, newels, etc., of sheet, hollow or solid stainless steel sections or with stainless steel balusters, balustrading or prepared to receive balustrading infill of other materials Stainless steel barriers and balustrading, with rails, bars, pipes, mesh screening, etc., of stainless steel or prepared to receive infill screening of other materials Infilling of glass, plastics, non-ferrous metal and other sheet or fabricated material to balustrades and barriers when supplied as part of the balustrading and railing Fixing all items and associated components to the building fabric including all bolts, cleats and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Purpose-made stainless steel lining to floor pits, trenches and recesses Purpose-made removable stainless steel floor covers, solid or grated, and associated frames and edging, to floor pits and trenches Proprietary manhole and inspection pit covers and frames Proprietary gratings and frames Purpose-made stainless steel hatches and frames to floor and roof openings, with opening gear Building in or securing frames to the building fabric with all necessary anchors, fixings, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Fire-rated stainless steel frames floor hatches and frames Fire-rated stainless steel covers and frames Fire-rated stainless steel access panels and frames

Stainless steel bollards, angle guards, rubbing strakes and column protection Stainless steel storage racks for general storage, pipes, etc. Stainless steel storage racks for cages, utensils, containers, etc. Stainless steel bicycle racks Stainless steel racks for gas cylinders Fabricated brackets and supports Stainless steel supports for signs, notices, lights, etc. Stainless steel proprietary and purpose made safes Stainless steel grates, grilles and trim to fireplaces Stainless steel access panels and frames Stainless steel edgings and fascias Stainless steel weatherbars when not supplied with the frames to openings Stainless steel decorative items Cast stainless steel items Stainless steel plaques, notices, signs, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes) Stainless steel screens (35-42) Thin stainless steel sheet items (35-51) Bollards, external (83-51) Bicycle racks, external (83-51)

Sheet stainless steel casing to structural members Sheet stainless steel box gutters, including supports Purpose-made sheet stainless steel linings to openings and recesses Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes) Proprietary sheet stainless steel linings to recesses for fire hose reels and equipment Stainless steel access panels

Fabricated aluminium stairs, tread and riser units, including supporting strings and framing for flights and landings, either with solid aluminium or grille treads and landings, or prepared to receive precast concrete or timber or laminated timber treads and landings Prefabricated aluminium stairs, including curved and helical stairs, with tread units, strings, and vertical supports Aluminium ladders, fixed to the building structure, with strings extended as handrails as required Safety hoops, etc., secured to aluminium ladders Proprietary or non-proprietary loft ladders including associated hatch doors Aluminium handrails, of hollow or solid section Aluminium stair balustrading, with rails, posts, uprights, newels, etc., of sheet, hollow or solid aluminium sections or with aluminium balusters or balustrading, or prepared to receive balustrading infill of other materials Aluminium barriers and balustrading, with rails, bars, pipes, mesh screening, etc., of aluminium or prepared to receive infill screening of other materials Infilling of glass, plastics, non-ferrous metal and other sheet or fabricated material to balustrades and barriers, when supplied as part of the balustrading and railing Fixing all items and associated components to the building fabric including all bolts, cleats, and other fixings Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Forming openings and cutting holes as required to suit subcontractor and General Contractor responsibility Non-fixed work (see Explanatory notes)

Purpose-made aluminium lining to floor pits, trenches and recesses Purpose-made removable aluminium floor covers, solid or grated, and associated frames and edging, to floor pits and trenches Proprietary manhole and inspection pit covers and frames Proprietary gratings and frames Purpose-made aluminium hatches and frames to floor and roof openings, with opening gear Building in or securing frames to the building fabric with all necessary anchors, fixings, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Aluminium angle guards, rubbing strakes and column protection Aluminium storage racks for general storage, pipes, etc. Aluminium storage racks for cages, utensils, containers, etc. Aluminium bicycle racks Fabricated brackets and supports Aluminium racks for gas cylinders Aluminium supports for signs, notices, lights, etc. Aluminium edgings and fascias Aluminium access panels and frames Aluminium weatherbars when not supplied with the frames to openings Cast aluminium items Aluminium decorative items Aluminium plaques, notices, signs, etc. Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Sheet aluminium casing to structural members Sheet aluminium box gutters, including supports Purpose-made sheet aluminium linings to openings and recesses Preparing surfaces and applying protective coatings and decorative finishes off site Preparing surfaces to receive protective coatings and decorative finishes on site Non-fixed work (see Explanatory notes)

Cast iron ladders and stairs, including helical stairs Cast iron stairs, balustrades and balcony railings and brackets Cast iron decorative items Cast iron fireplaces, grates and fireplace surrounds Cast iron flues, chimney coronets, etc. Cast iron plaques, notices, signs, etc.

Wrought iron decorative screens Wrought iron decorative items Wrought iron balustrading and barrier railings

Copper and copper alloy items Copper and copper alloy stairs and ladders Copper and copper alloy handrails, balustrades and railings Copper and copper alloy screens and frames Copper and copper alloy sheet fabricated items Copper and copper alloy miscellaneous items Copper and copper alloy plaques, notices, signs, etc. Copper and copper alloy box gutters and supports

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

No content available for this item.

Composite metal items and framing Composite metal ladders and stairs, including helical stairs Composite metal handrails, balustrades and railings Composite metal screens and shutters Composite metal sheet fabricated items Composite metal miscellaneous items

No content available for this item.

No content available for this item.

No content available for this item.